Application of Oscilloscope Probes in Crystal Oscillator Measurement Ⅱ

Oct 23, 2026 Leave a message

Application of Oscilloscope Probes in Crystal Oscillator Measurement

High Bandwidth's Core Value: Restoring True Signals

The fast edges of active crystal oscillators contain a large number of high-frequency harmonics. If the probe bandwidth is insufficient, these high-frequency components will be severely attenuated, causing the measured waveform edges to become slow and distorted. This fails to truly reflect the actual characteristics of the signal and directly affects the judgment of circuit performance.

info-1024-763

[Image: Oscilloscope screenshot showing a clean clock waveform]

Clean clock waveform measured with a high-bandwidth probe. The edges are steep and distortion-free, truly restoring the signal characteristics of the active crystal oscillator.

Loss of High-Frequency Harmonics: High-frequency components of the signal are filtered out, resulting in a loss of waveform detail and an inability to reflect the true frequency characteristics of the signal.

Edge Rate Distortion: The rising and falling edges are noticeably slowed, making it impossible to accurately measure the actual transition speed of the signal, which affects timing analysis.

Measurement Result Deviation: Distorted waveforms lead to inaccurate measurements of key parameters such as frequency and duty cycle, misleading circuit debugging and fault troubleshooting.

Advantages of a Short Ground Lead: Suppressing Ringing and Overshoot

The ground lead itself has parasitic inductance. In high-speed clock signal scenarios, the current change rate is extremely high, and even a tiny inductance value can produce a significant voltage drop. This directly causes distortion phenomena such as ringing and overshoot in the measured waveform, interfering with signal authenticity.

info-754-568

[Image: Oscilloscope screenshot showing signal ringing and overshoot due to a long ground lead]

Measured waveform: Signal ringing and overshoot distortion caused by a long ground lead.

Short Ground Lead (<1cm)

* Clean waveform, perfectly restoring the true signal.

* Overshoot/undershoot amplitude is almost negligible.

*No attenuation in high-frequency response. This is an essential condition for precise measurement.

Long Ground Lead (>3cm)

* Ringing and overshoot phenomena are significant.

* Severe signal distortion, unable to reflect the true level.

* The effect of parasitic inductance is amplified, and high-frequency characteristics completely fail.

Core Conclusion: A short ground lead is the key to accurately measuring high-speed signals. Active probes, with their integrated short ground lead design, can suppress parasitic inductance interference from the source, ensuring the precision and authenticity of measurement results.

II. Passive Crystal Oscillator Measurement Methods and Techniques

info-688-342

[Image: Illustration of physical connection of an active probe with a series compensation capacitor]

Figure: Illustration of physical connection of an active probe with a series compensation capacitor.

By physically connecting an extremely small high-frequency capacitor in series at the front end of the probe, the input capacitance of the probe itself can be effectively isolated, thereby reducing the load pulling effect on the passive crystal oscillator being measured and ensuring the accuracy of the measurement results.

Method 1: Series Capacitor to Further Reduce Load

For passive crystal oscillators that are extremely sensitive to load, connecting a small capacitor (e.g., 0.5pF) in series at the probe signal input can significantly reduce the equivalent input capacitance of the probe, thereby minimizing interference with the crystal's resonant frequency.

Parameter Calculation Example

Probe input capacitance (0.8pF) + series capacitance (0.5pF)

Equivalent capacitance: ≈ 0.31pF (Formula: Ceq = (C1 × C2) / (C1 + C2))

Practical Verification Suggestions

The actual value is affected by parasitic parameters of the PCB pad, trace, and capacitor accuracy. It is recommended to observe the waveform amplitude and frequency stability with an oscilloscope in the actual circuit, and fine-tune the capacitance value to achieve the best matching effect.

Method 2: Dual-Probe Evaluation of Frequency Offset

By using two identical probes, quantitatively evaluate the actual load impact of probe connection on the crystal frequency, providing precise data support for compensation and calibration of measurement errors.

① Connect the First Probe

After connecting the first probe, measure the frequency \(F_1\), calculate the frequency change value caused by a single connection \(\Delta F_1 = F_1 - F_0\), and record the initial offset data.

② Superimpose the Second Probe

Connect a second identical probe in parallel, measure the frequency \(F_2\), calculate the secondary offset amount \(\Delta F_2 = F_2 - F_1\), forming a dual-probe load comparison.

Analysis and Application Value

By comparing the difference between \(\Delta F_1\) and \(\Delta F_2\) , the degree of influence of the probe input capacitance on the crystal frequency can be accurately evaluated. This allows for the establishment of a mathematical compensation model to correct measurement results, eliminating systematic errors caused by the connection of test equipment, and improving the accuracy of high-frequency circuit parameter testing.

III. Impact of Ground Lead Length on Active Crystal Oscillator Measurement Results.

info-790-449

[Image: Oscilloscope screenshot showing clean waveform with a short ground lead]

Short Ground Lead (Active Probe)

The rising and falling edges of the waveform are steep, with no obvious ringing and overshoot, and the signal restoration degree is extremely high.

Advantages: Minimal parasitic inductance avoids interference, ensuring accurate and stable measurement of high-frequency signals.

info-1600-1200

[Image: Oscilloscope screenshot showing signal ringing and overshoot with a long ground lead]

Long Ground Lead (Ordinary Probe)

 

The waveform shows significant ringing and overshoot, resulting in poor signal integrity.

Cause:The long ground lead introduces large parasitic inductance, which resonates with the probe capacitance and causes waveform distortion.

Analysis Conclusion: The parasitic inductance of the long ground lead is the core cause of waveform distortion. The short ground lead of active probes suppresses parasitic effects and improves measurement accuracy, making it the preferred choice for high-speed digital signal analysis.

IV. Analysis of Experimental Results

info-806-442

[Image: Illustration comparing active and passive probe structures]

Active Probe: Ultimate Low-Load Design

Compact structure with an extremely short ground pin. Input capacitance is only about 0.8pF, which minimizes interference with the oscillator circuit being measured, ensuring the signal is not distorted.

info-612-340

Passive Probe: Conventional General-Purpose Tool

Simple structure and low cost, but with large input capacitance (typically 9~20pF).

It is prone to causing load effects on high-Q crystal oscillator circuits, leading to frequency shift or oscillation stop.

Experimental Conclusion: Active probes, with their extremely low input capacitance, are the ideal tool for measuring sensitive devices such as passive crystal oscillators. They can effectively prevent the probe from becoming an additional load, ensuring that the measurement results truly reflect the actual working state of the circuit.

V. Conclusion and Summary

Core Conclusion: The Essence of Measurement is "Not Changing"

① Active Crystal Oscillator Measurement

Core Advantages: High-bandwidth response and extremely short ground lead design, capable of effectively capturing high-speed signal details and reducing signal transmission loss.

Measurement Goal: Truly restore the original appearance of high-speed waveforms, avoid signal distortion caused by insufficient probe performance, and ensure that the observed signals are true and valid.

② Passive Crystal Oscillator Measurement

Core Advantages: Extremely low input capacitance characteristics, minimizing the impact of the probe on the crystal load and maintaining the original resonant conditions of the circuit.

Measurement Goal: Minimize changes to the inherent working state of the crystal during measurement, ensuring that the measurement results reflect the true frequency and stability of the crystal.

Final Summary: Good crystal oscillator measurement not only requires "being able to measure" but also achieving the goal of not changing the original state of the measured object as much as possible during the measurement process. Choosing the appropriate probe type is the core key to achieving precise and non-destructive measurement, and is also the foundation for ensuring the authenticity and reliability of R&D and test data.

VI. Conclusion and Summary

Key Indicator

Measured/Theoretical Value

Data Source

Confidence Level

Active Probe Input Capacitance

≈ 0.8 pF

Official Documentation

High

Ordinary Passive Probe Input Capacitance

≈ 10-20 pF

Official Documentation

High

Active Probe Rise Time

<350 ps

Official Documentation

High

Ordinary Passive Probe Rise Time

>1.5 ns

Official Documentation

High

Equivalent Capacitance After Series Capacitor

≈ 0.31 pF

Theoretical Calculation

Medium

Note: "High" confidence level indicates that the data comes from original documents or measured data released by authoritative organizations; "Medium" confidence level indicates derivation based on standard theoretical formulas combined with measured parameters; "Low" confidence level refers to estimates based on historical data. The data on this page is compiled based on the latest technical specifications in 2026.*